Cod: 1.14.0402.00002 - Nombre: CAN-Bus-Tester 2 (CBT2)

IXXAT

CAN-Bus-Tester 2 (CBT2) Powerful tool for analysis of CAN bus physics and CAN protocol

Powerful tool for analysis of
CAN bus physics and CAN protocol

The CAN-Bus-Tester 2 is a universal measuring instrument for the commissioning, analysis, monitoring, troubleshooting and maintenance of CAN bus systems.

Características destacadas

  • Support of CAN, CANopen, DeviceNet and SAE J1939 systems 
  • Analysis of the signal-to-noise ratio of all telegrams (level, flanks, faults)
  • Integrated oscilloscope with data interpretation for telegram analysis
  • Comprehensive trigger conditions for fault localization (logical and physical errors)
  • Monitoring of bus status, bus load, error telegrams
  • Wiring test (termination resistance, short circuits, interruptions, loop resistance, line length)
  • Automatic baud rate detection
  • Simple connection to CAN systems thanks to automatic baud rate detection and BusScan
  • Simple operation via Windows program
  • Simple generation of test protocols
  • CAN monitor for transmission and reception of CAN messages (optional)
Use CAN according to ISO 11898-2 (High-Speed) with 11-bit or 29-bit identifier (CAN 2.0A and 2.0B)
Baudrate 5 k, 10 k, 20 k, 33.3 k, 50 k, 62.5 k, 75 k, 83.3 k, 100 k, 125 k, 200 k, 250 k, 500 k, 800 k, 1000 kBit/s
Baudrate detection All supported baudrates
Bit scanning 64x, 10240 scanning points
Trigger output BNC-socket, electrically isolated
Connection to CAN bus Passive, 2 x 9-pole SUB-D connector
PC connection Via USB, electrically isolated
Supply voltage 9 ... 36 V DC, DIN 45323 low-voltage socket; 0.15 ... 0.55A
Dimensions and wight 40 x 134 x 170 mm (H/W/L), approx. 600 g; With case: 504 x 354 x 119 mm, approx. 5000 g
Safety/protection EN 60950: 2003-03 / IP 20 according to EN 60529
EMC EN 61000-3-2: 2000, +A1: 2000, +A2: 2004 EN 55022: 1998, +A1: 2000, +A2: 2003 EN 61000-6-2: 2001
Temperatur range Operation: +5 °C ... +40 °C; Storage: -20 °C ... +60 °C

Powerful tool for analysis of
CAN bus physics and CAN protocol

The CAN-Bus-Tester 2 is a universal measuring instrument for the commissioning, analysis, monitoring, troubleshooting and maintenance of CAN bus systems.


How it works

Typical faults during the operation of CAN bus systems, such as node failure, communication errors or complete system failure, are often caused by problems in the bus physics. Generally, devices which transmit messages with a low signal-to-noise ratio are highly susceptible to failures. The CAN-Bus-Tester provides an overview of the signal-to-noise ratios on the bus, enabling frequent causes of failures to be quickly identified and rectified. In addition, the most important logical analysis functions are also integrated into the Tester (otherwise found only in protocol analyzers).

The tester can be used for CAN bus systems with 11- or 29-bit identifier in accordance with ISO 11898-2 and supports as basis version the CAN layer-2 protocol. Using add-ons, the CBT can also support CANopen, DeviceNet and SAE J1939 based systems. This support can be enabled on the device at any time using the corresponding licenses. Automatic baud rate detection and the self-connecting BusScan allow the CAN-Bus-Tester to be quickly and easily connected to the system to be analyzed and started. The measurement results are automatically assigned to the relevant CAN identifiers or network nodes.

 


 

      

 

HMS also offers a CAN Monitor Tool (Receive/Transmit) as an add-on for the CBT, providing a new and freely scalable user interface which allows to use the advantages of high resolution displays. The tool displays the CAN messages, error frames and overrun frames. It allows to trigger on telegrams and comes with a function to display start/stop and pause notes in the reception window. Furthermore, in transmission mode the CAN telegrams can be collected within a list (sequences), which allows to send several CAN messages with defined time intervals, once or repeatedly.

Depending on the test strategy, various methods of identifying faults can be used, such as a fast overview of the complete system, monitoring of an individual node or setting various trigger events (physical and/or logical faults and error-frames). When the trigger function is used, all faults are defined up to the individual bit position, are provided with a time stamp and displayed in the integrated oscilloscope.
A trigger signal available via the external trigger output can be used to trigger an oscilloscope. A certain CAN message or an error telegram can thus be displayed selectively on the oscilloscope.

With the CAN-Bus-Tester 2, the bus wiring can be tested while the system is being set up and its transmission properties can be saved. During the complete lifetime, comparative measurements can be carried out directly on the running system and thus downtimes prevented.

The CAN-Bus-Tester is connected to a Windows PC via USB and operated with the software supplied. The measured values determined can also be saved or summarized in a detailed report. Logging data from the CANobserver can also be imported for inspection.

Technical specifications

Use CAN according to ISO 11898-2 (High-Speed) with 11-bit or 29-bit identifier (CAN 2.0A and 2.0B)
Baudrate 5 k, 10 k, 20 k, 33.3 k, 50 k, 62.5 k, 75 k, 83.3 k, 100 k, 125 k, 200 k, 250 k, 500 k, 800 k, 1000 kBit/s
Baudrate detection All supported baudrates
Bit scanning 64x, 10240 scanning points
Trigger output BNC-socket, electrically isolated
Connection to CAN bus Passive, 2 x 9-pole SUB-D connector
PC connection Via USB, electrically isolated
Supply voltage 9 ... 36 V DC, DIN 45323 low-voltage socket; 0.15 ... 0.55A
Dimensions and wight 40 x 134 x 170 mm (H/W/L), approx. 600 g; With case: 504 x 354 x 119 mm, approx. 5000 g
Safety/protection EN 60950: 2003-03 / IP 20 according to EN 60529
EMC EN 61000-3-2: 2000, +A1: 2000, +A2: 2004
EN 55022: 1998, +A1: 2000, +A2: 2003
EN 61000-6-2: 2001
Temperatur range Operation: +5 °C ... +40 °C; Storage: -20 °C ... +60 °C

 

System requirements

  • PC with 1.2 GHz or better, min. 256 MB RAM, graphics card with 24 bit color depth and 1024x768 pixel resolution, USB port, CD-ROM drive
  • Operating system Windows XP / Server2003 / Vista (32 & 64 Bit) / Windows7 (32 & 64 Bit)

 

Contents of delivery

  • Basic device CAN-Bus-Tester CBT 2
  • CAN bus accessories
    - 6 adapter cables: SUB-D, Open style, M12, 7/8”, SAE J1939-11, SAE-J1939-13
    - Shorting plug: SUB-D, Open style, M12, 7/8”, SAE J1939-11
    - Termination resistor: SUB-D, M12, 7/8”, SAE J1939-11
    - T- or Y-adapter: M12, 7/8”, SAE J1939-11
    - Adapter PCB for simple connection of an oscilloscope
  • Power unit 100 V - 240 V / 50-60 Hz; 24 V, 500 mA; power cable (EU, UK, USA/Japan)
  • BNC cable
  • USB cable
  • User's manual incl. CD with USB driver and application software
  • Robust and lockable case

  




Order number

1.14.0402.00001 CBT 2
CAN-Kit with measurement of CAN nodes and CAN Monitoring Tool
1.14.0402.00002 CBT 2
CAN+CANopen-Kit with add-ons for CANopen node identification, CAN Monitoring Tool and CANopen Monitoring Tool

 

Order numbers

for optional expansions

The optional extensions are additional software functions for the CBT2, which will be, if ordered, activated on the device via license key.

1.24.0402.00011 CAN Monitoring Tool
1.24.0402.00012 CANopen Monitoring Tool
1.24.0402.00001 CANopen Add-on
1.24.0402.00002 DeviceNet Add-on
1.24.0402.00003 SAE J1939 Add-on

 

Related products

Bienvenido a ER-Soft.
ER-Soft con la ley orgánica de protección de datos
Política de cookies.
Utilizamos cookies propias y de terceros para mejorar nuestros servicios y mostrarle publicidad relacionada con sus preferencias mediante el análisis de sus hábitos de navegación.
Si continúa navegando, consideramos que acepta su uso.
Más información pulsando aquí
X

¿Necesitas ayuda? Click

ayuda ER-Soft
X
Consulta a ER-Soft. *

 

*

 

* *Campos obligatorios.




X