Soluciones Wireless industrial de Acksys
Acksys

Soluciones Wireless industrial de Acksys


Soluciones Wireless industrial de Acksys


Acksys
 WLn-LINK-OEM

Código: WLn-LINK-OEM-TTL/R

WLn-LINK-OEM embedded module is a 2.4 / 5 GHz IEEE 802.1a/b/g/n solution designed to quickly and easily add wireless LAN to a wide range of wired Ethernet OEM products.
  • Complete ready-to-use solution (access point, bridge, repeater, Mesh point) requiring no driver software
  • Small sized PCB (L: 103 x l: 57 x H: 20 mm)
  • WiFi IEEE 802.11a/b/g/n 3T3R & Gigabits LAN interfaces, radio bit rates up to 450 Mbps
  • Secure WiFi link
  • Available in industrial temperature range
  • Web based configuration, SNMP administration
  • Reduces TTM, design risk & cost
    Ethernet interface   1-port Gigabit Ethernet 10/100/1000 Base TX auto-sensing, plug & play mode & auto MDI/MDIX cross-over, RJ45 or TTL Ethernet interface (HE10 connector)    
    Serial interface   One serial port (TTL level)    
    WiFi interface   1 radio IEEE 802.11 a/b/g/n, MIMO 3T3R, 2.4 / 5 Ghz    
    WiFi radio data rate   802.11a : 6, 9, 12, 18, 24, 36, 48 and 54 Mbps802.11b/g : 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48 and 54 Mbps802.11n : MCS0-23, 3 streams (6.5 to 450 Mbps)    
    Operating frequencies   ISM : 2.4-2.483 GHz (up to 14 channels)UNII : 5.15-5.25 GHz (up 4 channels)UNII-2 : 5.25-5.35 GHz (up to 4 channels)UNII-2 ext : 5.470-5.725 GHz (up to 11 channels)UNII-3 : 5.725-5.825 GHz (up to 4 channels)Supports DFS and TPC    
    Output power   Up to 24dBm (aggregate), depending on radio card model    
    Antennas   3 U.FL connectors    
    Security   IEEE 802.1x (RADIUS authenticator & supplicant), WPA2-PSK, WPA-PSK, WEP    
    WiFi Modes   Access point, client, repeater, MESH point (IEEE 802.11s), infrastructure, AD-HOC, client router, WMM QoS, multicast, dynamic routing and firewall modes fully supported, fast roaming (less than 30 ms), redundancy (VRRP)    
    Administration   Built-in WEB interface, SNMP agent, administration software for Windows/Linux (ACKSYS NDM)    
    LEDs Signaling   Radio : quality and activity | Ethernet : link 10/100/1000 and activity | Power : on-off | Product diagnostic    
    Power supply   +5VDC (+/- 5%), 8 Watts typical    
    Dimensions & weight   Small sized PCB, L: 103 x l: 57 x H: 20 mm, approx. 50g    
    Standards   Radio module CE and FCC certified. WLn-LINK-OEM has to be certified in the final product.    
    Environment   Operating temperature: -20°C to +70°C or -40°C to +85°C (for extended temperature range model)Storage: -65°C to +100°C, Humidity: 5% to 95% (non-condensing)    
    Warranty   1 year    

WLn-LINK-OEM

Acksys
 WLn-LINK-OEM

Código: WLn-LINK-OEM-EVAL/R

WLn-LINK-OEM embedded module is a 2.4 / 5 GHz IEEE 802.1a/b/g/n solution designed to quickly and easily add wireless LAN to a wide range of wired Ethernet OEM products.
  • Complete ready-to-use solution (access point, bridge, repeater, Mesh point) requiring no driver software
  • Small sized PCB (L: 103 x l: 57 x H: 20 mm)
  • WiFi IEEE 802.11a/b/g/n 3T3R & Gigabits LAN interfaces, radio bit rates up to 450 Mbps
  • Secure WiFi link
  • Available in industrial temperature range
  • Web based configuration, SNMP administration
  • Reduces TTM, design risk & cost
    Ethernet interface   1-port Gigabit Ethernet 10/100/1000 Base TX auto-sensing, plug & play mode & auto MDI/MDIX cross-over, RJ45 or TTL Ethernet interface (HE10 connector)    
    Serial interface   One serial port (TTL level)    
    WiFi interface   1 radio IEEE 802.11 a/b/g/n, MIMO 3T3R, 2.4 / 5 Ghz    
    WiFi radio data rate   802.11a : 6, 9, 12, 18, 24, 36, 48 and 54 Mbps802.11b/g : 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48 and 54 Mbps802.11n : MCS0-23, 3 streams (6.5 to 450 Mbps)    
    Operating frequencies   ISM : 2.4-2.483 GHz (up to 14 channels)UNII : 5.15-5.25 GHz (up 4 channels)UNII-2 : 5.25-5.35 GHz (up to 4 channels)UNII-2 ext : 5.470-5.725 GHz (up to 11 channels)UNII-3 : 5.725-5.825 GHz (up to 4 channels)Supports DFS and TPC    
    Output power   Up to 24dBm (aggregate), depending on radio card model    
    Antennas   3 U.FL connectors    
    Security   IEEE 802.1x (RADIUS authenticator & supplicant), WPA2-PSK, WPA-PSK, WEP    
    WiFi Modes   Access point, client, repeater, MESH point (IEEE 802.11s), infrastructure, AD-HOC, client router, WMM QoS, multicast, dynamic routing and firewall modes fully supported, fast roaming (less than 30 ms), redundancy (VRRP)    
    Administration   Built-in WEB interface, SNMP agent, administration software for Windows/Linux (ACKSYS NDM)    
    LEDs Signaling   Radio : quality and activity | Ethernet : link 10/100/1000 and activity | Power : on-off | Product diagnostic    
    Power supply   +5VDC (+/- 5%), 8 Watts typical    
    Dimensions & weight   Small sized PCB, L: 103 x l: 57 x H: 20 mm, approx. 50g    
    Standards   Radio module CE and FCC certified. WLn-LINK-OEM has to be certified in the final product.    
    Environment   Operating temperature: -20°C to +70°C or -40°C to +85°C (for extended temperature range model)Storage: -65°C to +100°C, Humidity: 5% to 95% (non-condensing)    
    Warranty   1 year    

WLn-LINK-OEM

Acksys
 WLg-LINK-OEM Compact access point, Ethernet bridge & repeater (WDS)

Código: WLg-LINK-OEM-RJ

When used in Access Point mode, the WLg-LINK-OEM is the root element of an industrial WiFi Ethernet network. When used as a Bridge, it makes it possible to connect any Ethernet 10/100 industrial equipment to this network.
  • IEEE 802.11 a/b/g/h & super AG standards, up to 108 Mbps data rate
  • Security: WEP, WPA-PSK, WPA2-PSK and IEEE 802.1x (RADIUS)
  • Easy to use web based configuration
  • Auto-sensing 10/100 Base TX network interface (TTL or RJ45)
  • +3.3VDC or +5VDC power supply
  • Small sized PCB (L: 89 x W: 51 x H: 20 mm)
    Ethernet link   10/100 Base TX Ethernet interface, RJ45 or TTL Ethernet interface (HE10 connector)    
    WiFi network   Compliant to the IEEE 802.11a/b/g/h 2.4 / 5 GHz standards, multi-country Roaming support (IEEE 802.11d); Dynamic Frequency Selection (DFS) support provides flexible selection of best frequency to allow mobility among all existing IEEE 802.11a/b/g/h networks; "ClearVoice" band provides non-overlapping channels for fast-speed data transmission; Transmission Power Control (TPC) offers flexibility to adjust RF output power, based on the ATHEROS’s AR5414 (AR5006XS) chip set.    
    Data rate   Up to 108 Mbps (Super AG mode)    
    Channels   13 channels (b/g modes), 8 channels (a mode), 11 channels (h mode)    
    Output power   Transmitter +20 dBm (TPC)    
    Sensitivity   Receiver -92 dBm for IEEE 802.11 a/g and -95 dBm for IEEE 802.11b    
    Antennas   2 Hirose UFL connectors enable to connect up to 2 antennas for diversity    
    Modulation   OFDM : BPSK, QPSK, 16QAM, 64QAM DSSS : DBPSK, DQPSK, CCK    
    Security   64/128 bits WEP, WPA-PSK, WPA2-PSK, IEEE 802.1x (RADIUS authenticator & supplicant), MAC addresses filtering, SSID broadcast control    
    Modes   Access point to build a WiFi network infrastructure, Bridge to connect any Ethernet equipments to this network and MODBUS/TCP wireless gateway, repeater (WDS), infrastructure, AD-HOC, bridge router & fast roaming (less than 50 ms) modes are supported    
    Administration   Thanks to its built-in WEB interface, the setup of the device is achieved using any web browser installed on your computer (Internet Explorer, Netscape, Mozilla ...), SNMP agent, ACKSYS NDM    
    Operating systems   Windows, Linux, UNIX as well as any operating system supporting TCP/IP    
    Signaling   LAN & WLAN activity on LEDs    
    Power supply   From +3.3VDC or +5VDC power source on an HE10 connector    
    Consumption   3.5 Watts typical, 5 Watts maximum    
    Dimensions   Small sized PCB L: 89 x W: 51 x H: 20 mm, 47 g    
    Environment   Operating temperature: -20°C to +70°C, storage: -65 to +100°C Humidity: 5% to 95% (non-condensing), please consult us for the -40°C to +85°C range    

WLg-LINK-OEM

Acksys
 WLg-LINK-OEM Compact access point, Ethernet bridge & repeater (WDS)

Código: WLg-LINK-OEM-TTL

When used in Access Point mode, the WLg-LINK-OEM is the root element of an industrial WiFi Ethernet network. When used as a Bridge, it makes it possible to connect any Ethernet 10/100 industrial equipment to this network.
  • IEEE 802.11 a/b/g/h & super AG standards, up to 108 Mbps data rate
  • Security: WEP, WPA-PSK, WPA2-PSK and IEEE 802.1x (RADIUS)
  • Easy to use web based configuration
  • Auto-sensing 10/100 Base TX network interface (TTL or RJ45)
  • +3.3VDC or +5VDC power supply
  • Small sized PCB (L: 89 x W: 51 x H: 20 mm)
    Ethernet link   10/100 Base TX Ethernet interface, RJ45 or TTL Ethernet interface (HE10 connector)    
    WiFi network   Compliant to the IEEE 802.11a/b/g/h 2.4 / 5 GHz standards, multi-country Roaming support (IEEE 802.11d); Dynamic Frequency Selection (DFS) support provides flexible selection of best frequency to allow mobility among all existing IEEE 802.11a/b/g/h networks; "ClearVoice" band provides non-overlapping channels for fast-speed data transmission; Transmission Power Control (TPC) offers flexibility to adjust RF output power, based on the ATHEROS’s AR5414 (AR5006XS) chip set.    
    Data rate   Up to 108 Mbps (Super AG mode)    
    Channels   13 channels (b/g modes), 8 channels (a mode), 11 channels (h mode)    
    Output power   Transmitter +20 dBm (TPC)    
    Sensitivity   Receiver -92 dBm for IEEE 802.11 a/g and -95 dBm for IEEE 802.11b    
    Antennas   2 Hirose UFL connectors enable to connect up to 2 antennas for diversity    
    Modulation   OFDM : BPSK, QPSK, 16QAM, 64QAM DSSS : DBPSK, DQPSK, CCK    
    Security   64/128 bits WEP, WPA-PSK, WPA2-PSK, IEEE 802.1x (RADIUS authenticator & supplicant), MAC addresses filtering, SSID broadcast control    
    Modes   Access point to build a WiFi network infrastructure, Bridge to connect any Ethernet equipments to this network and MODBUS/TCP wireless gateway, repeater (WDS), infrastructure, AD-HOC, bridge router & fast roaming (less than 50 ms) modes are supported    
    Administration   Thanks to its built-in WEB interface, the setup of the device is achieved using any web browser installed on your computer (Internet Explorer, Netscape, Mozilla ...), SNMP agent, ACKSYS NDM    
    Operating systems   Windows, Linux, UNIX as well as any operating system supporting TCP/IP    
    Signaling   LAN & WLAN activity on LEDs    
    Power supply   From +3.3VDC or +5VDC power source on an HE10 connector    
    Consumption   3.5 Watts typical, 5 Watts maximum    
    Dimensions   Small sized PCB L: 89 x W: 51 x H: 20 mm, 47 g    
    Environment   Operating temperature: -20°C to +70°C, storage: -65 to +100°C Humidity: 5% to 95% (non-condensing), please consult us for the -40°C to +85°C range    

WLg-LINK-OEM

Acksys
 WLg-DONGLE-OEM

Código: WLg-DONGLE-OEM-232

WLg-DONGLE-OEM gives access to any serial equipment from Windows, UNIX & Linux computers connected to your WiFi Ethernet TCP/IP network, making it possible to communicate between two distant serial equipments through the network, or directly with a peer t
  • IEEE 802.11 a/b/g/h & super AG standards
  • Security: WEP, WPA-PSK, WPA2-PSK and IEEE 802.1x (RADIUS)
  • Easy to use web based configuration, TELNET, SNMP & ACKSYS NDM
  • 250 Kbps serial RS232 or TTL interface
  • +3.3VDC or +5VDC power supply
  • Compact module (L : 89 x W : 57 x H : 19 mm)
    Serial port   Full RS232 (SUB D9 connector) or TTL (HE10 connector) serial interface, 250 Kbps    
    WiFi network   Compliant to the IEEE 802.11a/b/g/h 2.4 / 5 GHz standards, multi-country Roaming support (IEEE 802.11d); Dynamic Frequency Selection (DFS) support provides flexible selection of best frequency to allow mobility among all existing IEEE 802.11a/b/g/h networks; "ClearVoice" band provides non-overlapping channels for fast-speed data transmission; Transmission Power Control (TPC) offers flexibility to adjust RF output power, based on the ATHEROS’s AR5414 (AR5006XS) chip set, single channel fast roaming (< 50 ms)    
    Radio data rate   Up to 108 Mbps (Super AG mode)    
    Channels   13 channels (b/g modes), 8 channels (a mode), 11 channels (h mode)    
    Output power   Transmitter +20 dBm (TPC)    
    Sensitivity   Receiver -92 dBm for IEEE 802.11 a/g and -95 dBm for IEEE 802.11b    
    Antennas   2 Hirose UFL connectors enable to connect up to 2 antennas for diversity    
    Modulation   OFDM : BPSK, QPSK, 16QAM, 64QAM DSSS : DBPSK, DQPSK, CCK    
    Security   64/128 bits WEP, WPA-PSK, WPA2-PSK, IEEE 802.1x (RADIUS)    
    Modes   Support for TCP Client/Server, DHCP Client, TELNET RFC2217 extension, Telnet Server, COM port re-director (VIP), multipoint or point to point virtual link over UDP modes and MODBUS/TCP Client/Server, MODBUS/RTU & MODBUS/ASCII protocols, direct communication (ad hoc) or from access point    
    Administration   Thanks to its built-in WEB interface, the setup of the device is achieved using any web browser installed on your computer (Internet Explorer, Netscape, Mozilla ...), SNMP agent, ACKSYS NDM, TELNET from the serial link    
    Operating systems   Windows, Linux, UNIX as well as any operating system supporting TCP/IP    
    Signaling   TxD / RxD serial and WLAN radio activity on LEDs    
    Power supply   From +3.3VDC or +5VDC power source on an HE10 connector    
    Consumption   3.5 Watts typical, 5 Watts maximum    
    Dimensions   Small sized PCB (L: 89 x W: 57 x H: 19 mm)    
    Environment   Operating temperature: -20°C to +70°C, storage: -65 to +100°C Humidity: 5% to 95% (non-condensing)    

WLg-DONGLE-OEM

Acksys
 WLg-DONGLE-OEM

Código: WLg-DONGLE-OEM-TTL

WLg-DONGLE-OEM gives access to any serial equipment from Windows, UNIX & Linux computers connected to your WiFi Ethernet TCP/IP network, making it possible to communicate between two distant serial equipments through the network, or directly with a peer t
  • IEEE 802.11 a/b/g/h & super AG standards
  • Security: WEP, WPA-PSK, WPA2-PSK and IEEE 802.1x (RADIUS)
  • Easy to use web based configuration, TELNET, SNMP & ACKSYS NDM
  • 250 Kbps serial RS232 or TTL interface
  • +3.3VDC or +5VDC power supply
  • Compact module (L : 89 x W : 57 x H : 19 mm)
    Serial port   Full RS232 (SUB D9 connector) or TTL (HE10 connector) serial interface, 250 Kbps    
    WiFi network   Compliant to the IEEE 802.11a/b/g/h 2.4 / 5 GHz standards, multi-country Roaming support (IEEE 802.11d); Dynamic Frequency Selection (DFS) support provides flexible selection of best frequency to allow mobility among all existing IEEE 802.11a/b/g/h networks; "ClearVoice" band provides non-overlapping channels for fast-speed data transmission; Transmission Power Control (TPC) offers flexibility to adjust RF output power, based on the ATHEROS’s AR5414 (AR5006XS) chip set, single channel fast roaming (< 50 ms)    
    Radio data rate   Up to 108 Mbps (Super AG mode)    
    Channels   13 channels (b/g modes), 8 channels (a mode), 11 channels (h mode)    
    Output power   Transmitter +20 dBm (TPC)    
    Sensitivity   Receiver -92 dBm for IEEE 802.11 a/g and -95 dBm for IEEE 802.11b    
    Antennas   2 Hirose UFL connectors enable to connect up to 2 antennas for diversity    
    Modulation   OFDM : BPSK, QPSK, 16QAM, 64QAM DSSS : DBPSK, DQPSK, CCK    
    Security   64/128 bits WEP, WPA-PSK, WPA2-PSK, IEEE 802.1x (RADIUS)    
    Modes   Support for TCP Client/Server, DHCP Client, TELNET RFC2217 extension, Telnet Server, COM port re-director (VIP), multipoint or point to point virtual link over UDP modes and MODBUS/TCP Client/Server, MODBUS/RTU & MODBUS/ASCII protocols, direct communication (ad hoc) or from access point    
    Administration   Thanks to its built-in WEB interface, the setup of the device is achieved using any web browser installed on your computer (Internet Explorer, Netscape, Mozilla ...), SNMP agent, ACKSYS NDM, TELNET from the serial link    
    Operating systems   Windows, Linux, UNIX as well as any operating system supporting TCP/IP    
    Signaling   TxD / RxD serial and WLAN radio activity on LEDs    
    Power supply   From +3.3VDC or +5VDC power source on an HE10 connector    
    Consumption   3.5 Watts typical, 5 Watts maximum    
    Dimensions   Small sized PCB (L: 89 x W: 57 x H: 19 mm)    
    Environment   Operating temperature: -20°C to +70°C, storage: -65 to +100°C Humidity: 5% to 95% (non-condensing)    

WLg-DONGLE-OEM

Acksys
 Ethernet Air-Pack Ready-to-use point-to-point wireless Ethernet bridge

Código: Ethernet Air-PACK

Ethernet-Air-Pack is a ready-to-use solution designed to replace any Ethernet cable between equipments (PC, IP video, printers ...), replace the network cable between the RJ45-wall outlet and the computer or even to establish a wireless bridge between two
  • Connection between two equipments or two networks
  • Ready to use, nothing to configure
  • 5 GHz IEEE 802.11a WiFi band (108 Mbps)
  • Secured radio link with pre-configured WPA2
  • 10/100 Base TX RJ45 auto-sensing network interface
  • AC/DC block adapters supplied
    Ethernet link     10/100 Base TX Ethernet interface, RJ45 connector  
    Radio link     Compliant with WiFi IEEE 802.11a, data rate up to 108 Mbps    
    Power, sensitivity     Transmitter +20 dBm, Receiver –92 dBm, one 5 GHz 2 dBi antenna    
    Signaling     LAN & WLAN activity on LEDs    
    Administration   SNMP and ACKSYS NDM    
    Power supply   +9VDC to +48VDC power source, PHOENIX connector, 3.5 Watts typical, 5 Watts maximum    
    Dimensions & weight     Small sized enclosure L: 103 x W: 67 x H: 23 mm, weight 225 g    
    Environment   Operating temperature: 0°C to +70°C, storage: -40°C to +80°C Humidity: 5% to 95% (non-condensing)    

Ethernet Air-Pack

Acksys
 PMXNOW0300 WiFi access point, 3-port Ethernet bridge & repeater (WDS)

Código: PMXNOW0300

PMXNOW0300 is a single slot backplane compatible module that allows the M340/M580 processors to interface easily with the WiFi wireless network in order to communicate with devices located remotely.
  • Direct connection to M340/M580, single slot backplane compatible module
  • Hot swappable module during operation for simplified maintenance
  • WiFi IEEE 802.11 a/b/g (2.4 / 5 / 5.4 GHz), up to 108 Mbps
  • Up to 5 Km range with external antenna, 300m LOS with standard antenna
  • Security : WEP, WPA-PSK, WPA2-PSK & IEEE 802.1X RADIUS
  • Web based configuration, SNMP administration
  • 3-port auto-sensing 10/100 Base TX, auto MDI-MDIX network interface
    Ethernet link   3-port Ethernet 10/100 auto-sensing, plug & play mode & auto MDI/MDIX cross-over One port is reserved for the M340/M580 CPU or M340/M580 NOE connection. When connected to the M340/M580 Ethernet port, PMXNOW0300 ports are considered as “Slave”. If connected to the M340/M580 NOE Ethernet port instead, PMXNOW0300 ports are considered as “Master”, distributed I/O operation is then fully supported (I/O Scanner).    
    WiFi network   Compliant to the IEEE 802.11a/b/g/h 2.4 / 5 GHz standards, multi-country Roaming support (IEEE 802.11d); Dynamic Frequency Selection (DFS) support provides flexible selection of best frequency to allow mobility among existing networks; "ClearVoice" band provides non-overlapping channels for fast data transmission; Transmission Power Control (TPC) offers flexibility to adjust RF output power.    
    Data rate   Up to 108 Mbps (Super AG mode)    
    Channels   2.4 GHz (802.11b/g): 14 channels / 5 GHz (801.11a/h): 24 channels    
    Output power   Transmitter +20 dBm (100 mW) with Transmit Power Control (TPC)    
    Sensitivity   Receiver -92 dBm for IEEE 802.11 a/g and -95 dBm for IEEE 802.11b    
    Antenna   2dBi 2.4 / 5 / 5.4 GHz antenna, RP-SMA connector    
    Modulation   OFDM: BPSK, QPSK, 16QAM, 64QAM and DSSS: DBPSK, DQPSK, CCK    
    Security   64/128 bits WEP, WPA-PSK, WPA2-PSK, IEEE 802.11x (RADIUS authenticator & supplicant), MAC addresses filtering, SSID broadcast control    
    Modes   Access point to build a WiFi network infrastructure, Bridge to connect any Ethernet, MODBUS/TCP or Ethernet/IP equipments to this network, repeater (WDS), infrastructure, AD-HOC, bridge router & fast roaming (less than 50 ms) modes are supported    
    Administration   Thanks to its built-in WEB interface, the setup of the device is achieved using any web browser installed on your computer (Internet Explorer, Netscape, Mozilla ...), SNMP agent, ACKSYS NDM    
    Signaling   LEDs signaling for LAN, WLAN network activity, 10/100 mode and RF level    
    Power Supply   Powered from M340/M580 +24VDC backplane    
    Consumption   3.5 W typical power consumption    
    Hot swap   Module is hot swappable during operation for simplified maintenance    
    Dimensions & weight   Small sized enclosure L: 97 x W: 32 x H: 104 mm, weight 200 g    
    Environment   Operating temperature: -20°C to +70°C (HR 5-95% non-condensing), storage: -40°C to +80°C    

PMXNOW0300

Acksys
 WLg-4LAN WiFi access point and bridge with 4-port Ethernet switch

Código: WLg-4LAN

When used in access point mode, WLg-4LAN is the root element of an industrial WiFi Ethernet network. When used as bridge, it allows connecting up to 4 Ethernet 10/100 devices to this network.
  • IEEE 802.11 a/b/g/h & super AG standards, up to 108 Mbps data rate
  • Security: WEP, WPA-PSK, WPA2-PSK and IEEE 802.1x (RADIUS)
  • Easy to use web based configuration
  • 4-port Ethernet switch 10/100 Base TX RJ45 auto-sensing network interface
  • +9VDC to +48VDC power supply
  • Small sized enclosure (L: 91 x W: 122 x H: 24 mm)
  Ethernet link     4-port 10/100 Base TX interface, RJ45 connectors    
    WiFi network     Compliant to the IEEE 802.11a/b/g/h 2.4 / 5 GHz standards, multi-country Roaming support (IEEE 802.11d); Dynamic Frequency Selection (DFS) support provides flexible selection of best frequency to allow mobility among all existing IEEE 802.11a/b/g/h networks; "ClearVoice" band provides non-overlapping channels for fast-speed data transmission; Transmission Power Control (TPC) offers flexibility to adjust RF output power, based on the ATHEROS’s AR5414 (AR5006XS) chip set.    
    Data rate     Up to 108 Mbps (Super AG mode)  
    Channels     13 channels (b/g modes), 8 channels (a mode), 11 channels (h mode)  
    Output power     Transmitter +20 dBm (TPC)    
    Sensitivity     Receiver -92 dBm for IEEE 802.11 a/g and -95 dBm for IEEE 802.11b    
    Antennas     Two 2dBi 2.4 / 5 GHz antennas (RP-SMA connectors)  
    Modulation     OFDM : BPSK, QPSK, 16QAM, 64QAM DSSS : DBPSK, DQPSK, CCK    
    Security     64/128 bits WEP, WPA-PSK, WPA2-PSK, IEEE 802.1x (RADIUS authenticator & supplicant), MAC addresses filtering, SSID broadcast control    
    Modes   Access point to build a WiFi network infrastructure, Bridge to connect any Ethernet equipments to this network and MODBUS/TCP wireless gateway, repeater (WDS), infrastructure, AD-HOC, bridge router & fast roaming (less than 50 ms) modes are supported    
    Administration     Thanks to its built-in WEB interface, the setup of the device is achieved using any web browser installed on your computer (Internet Explorer, Netscape, Mozilla ...), SNMP agent, ACKSYS NDM    
    Operating systems     Windows, Linux, UNIX as well as any operating system supporting TCP/IP    
    Signaling     LAN & WLAN activity on LEDs    
    Power supply   +9VDC to +48VDC power source, 3-pin Phoenix terminal block    
    Consumption     3.5 Watts typical, 5 Watts maximum    
    Dimensions & weight     Compact size enclosure L: 91 x W: 122 x H: 24 mm, weight 243 g    
    Environment   Operating temperature: -20°C to +70°C, storage: -65 to +100°C Humidity: 5% to 95% (non-condensing)    

WLg-4LAN

Acksys
 WLg-LINK Compact access point, Ethernet bridge & repeater (WDS)

Código: WLg-LINK

When used in the Access Point mode, the WLg-LINK is the root element of an industrial WiFi Ethernet network. When used as a Bridge, it makes it possible to connect any Ethernet 10/100 industrial equipment to this network.
  • IEEE 802.11 a/b/g/h & super AG standards, up to 108 Mbps data rate
  • Security: WEP, WPA-PSK, WPA2-PSK and IEEE 802.1x (RADIUS)
  • Easy to use web based configuration
  • Auto-sensing 10/100 Base TX RJ45 network interface
  • +9VDC to +48VDC power supply
  • Small sized enclosure (L: 103 x W: 67 x H: 24 mm)
  Ethernet link     10/100 Base TX Ethernet interface, RJ45 connector    
    WiFi network     Compliant to the IEEE 802.11a/b/g/h 2.4 / 5 GHz standards, multi-country Roaming support (IEEE 802.11d); Dynamic Frequency Selection (DFS) support provides flexible selection of best frequency to allow mobility among all existing IEEE 802.11a/b/g/h networks; "ClearVoice" band provides non-overlapping channels for fast-speed data transmission; Transmission Power Control (TPC) offers flexibility to adjust RF output power, based on the ATHEROS’s AR5414 (AR5006XS) chip set.    
    Data rate     Up to 108 Mbps (Super AG mode)  
    Channels     13 channels (b/g modes), 8 channels (a mode), 11 channels (h mode)  
    Output power     Transmitter +20 dBm (TPC)    
    Sensitivity     Receiver -92 dBm for IEEE 802.11 a/g and -95 dBm for IEEE 802.11b    
    Antennas     Two 2dBi 2.4 / 5 GHz antennas (RP-SMA connectors)  
    Modulation     OFDM : BPSK, QPSK, 16QAM, 64QAM DSSS: DBPSK, DQPSK, CCK    
   Security     64/128 bits WEP, WPA-PSK, WPA2-PSK, IEEE 802.1x (RADIUS authenticator & supplicant), MAC addresses filtering, SSID broadcast control    
    Modes     Access point to build a WiFi network infrastructure, Bridge to connect any Ethernet equipments to this network and MODBUS/TCP wireless gateway, repeater (WDS), infrastructure, AD-HOC, bridge router & rapid roaming (less than 50 mS) modes are supported    
    Administration     Thanks to its built-in WEB interface, the setup of the device is achieved using any web browser installed on your computer (Internet Explorer, Netscape, Mozilla ...), SNMP agent, ACKSYS NDM    
    Operating systems     Windows, Linux, UNIX as well as any operating system supporting TCP/IP  
   Signaling     LAN & WLAN activity on LEDs    
   Power supply     +9VDC to +48VDC power source, 3-pin Phoenix terminal block    
   Consumption     3.5 Watts typical, 5 Watts maximum    
   Dimensions & weight     Small sized enclosure L: 103 x W: 67 x H: 24 mm, weight 225 g    
   Environment     Operating temperature: 0°C to +70°C, storage: -65 to +100°C Humidity: 5% to 95% (non-condensing)    

WLg-LINK

Acksys
 WLg-DONGLE

Código: WLg-DONGLE

WLg-DONGLE gives access to any serial equipment from Windows, UNIX & Linux computers connected to your WiFi Ethernet TCP/IP network, make it possible to communicate between two distant serial equipments through the network, or directly with a peer to peer
  • IEEE 802.11 a/b/g/h & super AG standards
  • Security: WEP, WPA-PSK, WPA2-PSK and IEEE 802.1x (RADIUS)
  • Easy to use web based configuration, TELNET, SNMP & ACKSYS NDM
  • 250 Kbps serial RS232
  • +5VDC power supply
  • Compact metallic case (L : 103 x W : 67 x H : 24 mm)
    Serial port     Full RS232 (SUB D9 connector) serial interface, 250 Kbps    
    WiFi network     Compliant to the IEEE 802.11a/b/g/h 2.4 / 5 GHz standards, multi-country Roaming support (IEEE 802.11d); Dynamic Frequency Selection (DFS) support provides flexible selection of best frequency to allow mobility among all existing IEEE 802.11a/b/g/h networks; "ClearVoice" band provides non-overlapping channels for fast-speed data transmission; Transmission Power Control (TPC) offers flexibility to adjust RF output power, based on the ATHEROS’s AR5414 (AR5006XS) chip set, single channel rapid roaming (< 50 mS)    
    Radio data rate     Up to 108 Mbps (Super AG mode)  
    Channels     13 channels (b/g modes), 8 channels (a mode), 11 channels (h mode)  
    Output power     Transmitter +20 dBm (TPC)    
    Sensitivity     Receiver -92 dBm for IEEE 802.11 a/g and -95 dBm for IEEE 802.11b    
    Antenna     One 2 dBi bi-band external antenna, RP-SMA connector  
   Modulation     OFDM: BPSK, QPSK, 16QAM, 64QAM DSSS: DBPSK, DQPSK, CCK    
   Security     64/128 bits WEP, WPA-PSK, WPA2-PSK, IEEE 802.1x (RADIUS)    
    Modes     Support for TCP Client/Server, DHCP Client, TELNET RFC2217 extension, Telnet Server, COM port re-director (VIP), multipoint or point to point virtual link over UDP modes and MODBUS/TCP Client/Server, MODBUS/RTU & MODBUS/ASCII protocols, direct communication (ad hoc) or from access point    
    Administration     Thanks to its built-in WEB interface, the setup of the device is achieved using any web browser installed on your computer (Internet Explorer, Netscape, Mozilla ...), SNMP agent, ACKSYS NDM, TELNET from the serial link    
    Operating systems     Windows, Linux, UNIX as well as any operating system supporting TCP/IP    
    Signaling     TxD / RxD serial and WLAN radio activity on LEDs    
    Power supply     +5VDC power source on jack connector    
    Consumption     3.5 Watts typical, 5 Watts maximum    
    Dimensions     Compact metallic enclosure (L: 103 x W: 67 x H: 24 mm)    
    Environment     Operating temperature: -0°C to +70°C, storage: -65 to +100°C Humidity: 5% to 95% (non-condensing)    

WLg-DONGLE

Acksys
 RailBox Rugged dual 802.11ac WiFi access point, client & repeater for railways

Código: RailBox/RRXB

RailBox is a rugged device designed for railway and light rail applications. It can be mounted in trains, subways, trams or in any equipment that requires robustness and mobility.
  • Single or dual radio 802.11a/b/g/n/ac (MIMO 3T3R), up to 1.3 Gbps (radio bit rate), optional LTE mobile broadband router and GPS (coming soon)
  • MESH, WMM QoS, multiple SSID and centralized RADIUS security supported
  • Supports DFS and TPC
  • Auto-sensing Gigabit 10/100/1000 Base TX auto MDI/MDIX network interface
  • Dual insulated redundant power supply input (24 to 110 VDC EN50155 nominal or 12 to 36 VDC) or PoE+
  • Shock & vibration proof, rugged aluminum enclosure, IP66 seal rating
    Ethernet link   2-port Gigabit Ethernet 10/100/1000 auto-sensing, water and vibration proof rapid connect 8-point M12 X-coded connectors (CAT-6A) plug & play mode & auto MDI/MDIX cross-over, optional Ethernet bypass that redirects the network traffic in case of device or power supply failure (for daisy chain topologies)    
    WiFi network   1 or 2 radios IEEE 802.11a/b/g/n or IEEE 802.11a/b/g/n/ac, MIMO 3T3R, 2.4 / 5 GHz    
    Wireless WAN/GPS   Optional (coming soon) : LTE mobile broadband router, dual SIM, GPS receiver    
    WiFi radio data rate   802.11a: 6, 9, 12, 18, 24, 36, 48 and 54 Mbps802.11b/g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48 and 54 Mbps802.11n: MCS0-7, 3 streams (6.5 to 450 Mbps)802.11ac: MCS0-9, 3 streams (6.5 Mbps to 1.3 Gbps)    
    Operating frequencies   ISM : 2.4-2.483 GHz (up to 14 channels)UNII : 5.15-5.25 GHz (up 4 channels)UNII-2 : 5.25-5.35 GHz (up to 4 channels)UNII-2 ext : 5.470-5.725 GHz (up to 11 channels)UNII-3 : 5.725-5.825 GHz (up to 4 channels) Supports DFS and TPC    
    Output power   Up to 24 dBm (aggregate), depending on radio card model    
    Radio connectors   3 or 6 QMA connectors (no antenna provided)    
    Security   IEEE 802.1x (centralized RADIUS authenticator & supplicant), WPA2-PSK, WPA-PSK, legacy WEP supported    
    WiFi Modes   Access point, client, repeater, MESH point (IEEE 802.11s), infrastructure, AD-HOC, client router, WMM QoS, multicast, VPN, dynamic routing and firewall modes fully supported, fast roaming (less than 30 ms), redundancy (VRRP), carriage coupling system (SRCC)    
    Administration   Built-in WEB interface, the setup of the device is achieved using any web browser, SNMP agent, administration software for Windows/Linux (ACKSYS NDM), save / restore configuration key (C-Key)    
    LEDs Signaling   Radio : quality, activity and status | Ethernet : link 10/100/1000, activity | Power : on-off    
    Alarms & Inputs   One solid state relay output warning (with configurable action), 1 Form A, 60VDC 0.1A max & one input for external device control 24VDC max (3-pin Waterproof M8 connector)    
    Power supply   Dual insulated redundant input (1500V insulation, M12 connectors 4-pole A-coded) 24 to 110 VDC (EN50155 nominal) or 12 to 36 VDC depending on the model, with ground lug. PoE + (IEEE 802.3at Type 2 Class 4) model with ground lug also available.    
    Consumption   16W typical power consumption (dual radio), 20W max    
    Dimensions & weight   Product : compact shockproof rugged aluminum enclosure, (L: 80 x l: 175 x h: 57 mm), 900gRemovable fixing plate : 4-point fixing plate with ground lug (L: 80 x l: 225 x h: 4 mm), 200g    
    Standards   Safety : EN45545-2 (HL3), NF F16-101 (I1F1) (Fire and Smoke) / EN60950-1Radio : EN300-328 1.8.1 (2.4 GHz), EN301-893 1.7.1 (5 GHz, DFS)EMC : EN50155 / EN50121-3.2, EN301-489-1, EN301-489-17Environmental : EN61373 (shocks and vibration), EN60068 (climatic)    
    Environment   IP66 seal ratingOperating temperature: -25°C to +70°C (HR 0-99%) or extended -40°C to +85°C, storage: -40°C to +80°CGORE ® protective vent (dehumidifying membrane)    

RailBox

Acksys
 WLn-RailBox Dual 11n WiFi access point, client, repeater & MESH point for railways

Código: WLn-RailBox/R[P]

WLn-RailBox is a rugged device designed for railway and light rail applications. It can be mounted in trains, subways, trams for positive train control (PTC), fare collection, maintenance, remote management, wayside and track monitoring and in any equipme
  • Single or dual radio 11 a/b/g/n (MIMO 3T3R), up to 450 Mbps (radio bit rate)
  • MESH, WMM QoS, multiple SSID and centralized RADIUS security supported
  • Supports DFS and TPC
  • Auto-sensing Gigabit 10/100/1000 Base TX auto MDI/MDIX network interface
  • DC insulated power supply input (+24VDC to +110VDC) or PoE+ IEEE 802.3at
  • Shock & vibration proof, rugged aluminum enclosure, IP66 seal rating
    Ethernet link   2-port Gigabit Ethernet 10/100/1000 auto-sensing, waterproof ultra-lock 8-point M12 X-coded connectors (CAT-6A) plug & play mode & auto MDI/MDIX cross-over    
    WiFi network     1 or 2 radios compliant to the IEEE 802.11a/b/g/n, MIMO 3T3R, 2.4 / 5 GHz standards    
    Radio data rate     450 Mbps (3 streams)  
    Operating frequencies   ISM : 2.4-2.483 GHz (up to 14 channels)UNII : 5.15-5.25 GHz (up 4 channels)UNII-2 : 5.25-5.35 GHz (up to 4 channels)UNII-2 ext : 5.470-5.725 GHz (up to 11 channels)UNII-3 : 5.725-5.825 GHz (up to 4 channels)Supports DFS and TPC    
    Output power     Transmitter +20 dBm nominal  
    Sensitivity     Receiver -92 dBm for IEEE 802.11 a/g/n and -95 dBm for IEEE 802.11b  
    Antennas connections     3 or 6 QMA connectors for the WiFi (no antenna provided)    
    Modulation     OFDM: BPSK, QPSK, 16QAM, 64QAM / DSSS: DBPSK, DQPSK, CCK    
    Security     64/128 bits WEP, WPA-PSK, WPA2-PSK, IEEE 802.1x (centralized RADIUS authenticator & supplicant), MAC addresses filtering, SSID broadcast control    
    WiFi Modes   Access point to build a WiFi network infrastructure, client to connect any Ethernet equipments to this network, repeater, MESH point (IEEE 802.11s), infrastructure, AD-HOC, client router, WMM QoS, multicast, VPN, dynamic routing and firewall modes are fully supported, fast roaming (less than 30 ms), redundancy (VRRP)    
    Administration     Built-in WEB interface, the setup of the device is achieved using any web browser, SNMP agent, ACKSYS NDM, C-Key (save / restore configuration key)    
    Operating systems     Windows, Linux, UNIX as well as any operating system supporting TCP/IP  
    Signaling     LEDs signaling radio quality, activity and status, Link 10/100/1000 and activity for the LAN port    
    Power supply     +24VDC to +110VDC EN 50155 nominal, 1500V insulation, dual input (ultra-lock waterproof M12 connector 4-pole A-coded)or PoE + (IEEE 802.3at) power supply with ground lug    
    Consumption   16W typical power consumption (dual radio)    
    Dimensions & weight   Compact shockproof rugged aluminum enclosure, (L: 80 x l: 175 x h: 57 mm), 840gRemovable fixing plate : 4-point fixing plate with ground lug (L: 80 x l: 225 x h: 4 mm), 200g    
    Standards     EN 301489-17 & EN 61000-6-2 (CEM), IP66 seal rating,EN 50155 (IEC 60571), EN 50121-3-2, EN 50121-4 (railways ground & rolling stock)    
    Environment     Operating temperature: -25°C to +70°C (HR 0-99%) or extended -40°C to +75°C, storage: -40°C to +80°C    

WLn-RailBox

Acksys
 WLg-xROAD-S

Código: WLg-xROAD/S

WLg-xROAD/S gives access to any serial equipments from Windows, UNIX & Linux computers connected to your WiFi Ethernet TCP/IP network, make it possible to communicate between two distant serial equipments through the network, or directly with a peer to pe
  • Serial RS232 / RS422 / RS485 full duplex up to 250 Kbps
  • 9-50 VDC wide range power supply
  • IEEE 802.11 a / b / g /h WiFi radio (2.4 / 5 GHz)
  • MIL-STD-810 shockproof and vibration proof rugged aluminum enclosure, IP65
  • Point to Point (virtual cable) & multipoint modes, virtual COM port redirector (ViP)
  • TCP Client / Server, UDP & MODBUS/TCP support
    Serial port   Full RS232 / 4222 / 485 (SUB D9 connector) serial interface, 250 Kbps    
    RS signals   RS232 mode: TxD, RxD, RTS, DTR, CTS, DCD, DSR, RI RS422/485 mode: -Tx, +Tx, -Rx, +Rx (+RX and –RX signals can be polarized with jumpers)    
    Cable connection     9-point terminal block for RS signals, 2-point for power supply, stuffing box cable output    
    WiFi network     Compliant to the IEEE 802.11a/b/g/h 2.4 / 5 GHz standards, multi-country Roaming support (IEEE 802.11d); Dynamic Frequency Selection (DFS) support provides flexible selection of best frequency to allow mobility among all existing IEEE 802.11a/b/g/h networks; "ClearVoice" band provides non-overlapping channels for fast-speed data transmission; Transmission Power Control (TPC) offers flexibility to adjust RF output power, based on the ATHEROS’s AR5414 (AR5006XS) chip-set, single channel fast roaming (<50 ms)    
    Radio data rate     Up to 108 Mbps (Super AG mode)  
    Channels     13 channels (b/g modes), 8 channels (a mode), 11 channels (h mode)  
    Output power     Transmitter +20 dBm (TPC)  
    Sensitivity   Receiver -92 dBm for IEEE 802.11 a/g and -95 dBm for IEEE 802.11b    
    Antenna   One 2 dBi bi-band external antenna, RP-SMA connector    
    Modulation     OFDM : BPSK, QPSK, 16QAM, 64QAM DSSS : DBPSK, DQPSK, CCK    
    Security   64/128 bits WEP, WPA-PSK, WPA2-PSK, IEEE 802.1x (RADIUS)    
    Modes     Support for TCP Client/Server, DHCP Client, TELNET RFC2217 extension, Telnet Server, COM port re-director (VIP), multipoint or point to point virtual link over UDP modes and MODBUS/TCP Client/Server, MODBUS/RTU & MODBUS/ASCII protocols, direct communication (ad hoc) or from access point    
    Administration     Thanks to its built-in WEB interface, the setup of the device is achieved using any web browser installed on your computer (Internet Explorer, Netscape, Mozilla ...), SNMP agent, ACKSYS NDM, TELNET from the serial link    
    Operating systems     Windows, Linux, UNIX as well as any operating system supporting TCP/IP    
    Signaling   Serial TxD & RxD, WLAN, mode, diagnostic and power (LEDs)    
    Power supply   +9VDC to +50VDC, 3.5 Watts typical    
    Dimensions   Rugged aluminum enclosure (L: 115 mm x W: 64 mm x H: 35 mm) Weight: 330g (with the 40 cm serial cable)    
    Standards     MIL-STD-810F methods 514.5 & 516.5 (shocks & vibrations), IP65 seal rating EN 301489-17 & EN 61000-6-2 (CEM), E-marked    
    Environment   Operating temperature: -25°C to +70°C, storage: -40°C to +80°C Humidity: 0% to 99% (non-condensing)    

WLg-xROAD/S

Acksys
 WLg-xROAD-N

Código: WLg-xROAD/N

WLg-xROAD/N is a rugged equipment designed for applications in road transportation, depots, warehouses, agriculture, manufacturing floors, docks, distribution centers, shipyards and lumberyards … it can be mounted in trucks, city buses, forklifts, trailer
  • WiFi IEEE 802.11 a/b/g/h & super AG, up to 108 Mbps
  • Security : WEP, WPA-PSK, WPA2-PSK & IEEE 802.1x RADIUS
  • Web based configuration, SNMP administration
  • Auto-sensing 10/100 Base TX network interface
  • DC power supply input (+9VDC to +50VDC), POE IEEE 802.3af for /NP
  • Shock & vibration proof rugged aluminum enclosure, IP65 seal rating
  Ethernet link     10/100 auto-sensing Ethernet port (terminal block inside the enclosure), plug & play mode & auto MDI/MDIX cross-over    
    WiFi network     Compliant to the IEEE 802.11a/b/g/h 2.4 / 5 GHz standards, multi-country Roaming support (IEEE 802.11d); Dynamic Frequency Selection (DFS) support provides flexible selection of best frequency to allow mobility among existing networks; "ClearVoice" band provides non-overlapping channels for fast data transmission; Transmission Power Control (TPC) offers flexibility to adjust RF output power, based on ATHEROS’s AR5414 (AR5006XS) chip set.    
    Data rate     Up to 108 Mbps (Super AG mode)  
    Channels   13 channels (b/g modes), 8 channels (a mode), 11 channels (h mode)    
    Output power     Transmitter +20 dBm (TPC)    
    Sensitivity     Receiver -92 dBm for IEEE 802.11 a/g and -95 dBm for IEEE 802.11b    
    Antenna     One 2dBi 2.4 / 5 GHz antenna, RP-SMA connector  
    Modulation     OFDM: BPSK, QPSK, 16QAM, 64QAM and DSSS: DBPSK, DQPSK, CCK  
    Security     64/128 bits WEP, WPA-PSK, WPA2-PSK, IEEE 802.1x (RADIUS authenticator & supplicant), MAC addresses filtering, SSID broadcast control    
    Modes   Access point to build a WiFi network infrastructure, Bridge to connect any Ethernet equipments to this network and MODBUS/TCP wireless gateway, repeater (WDS), infrastructure, AD-HOC, bridge router & fast roaming (less than 50 ms) modes are supported    
    Administration     Thanks to its built-in WEB interface, the setup of the device is achieved using any web browser installed on your computer (Internet Explorer, Netscape, Mozilla ...), SNMP agent, ACKSYS NDM    
    Operating systems     Windows, Linux, UNIX as well as any operating system supporting TCP/IP    
    Signaling     LEDs signaling for LAN, WLAN network activity, 10/100 mode, power supply    
    Power supply     DC power supply (+9VDC to +50VDC) or POE IEEE 802.3af (for the /NP model)    
    Consumption   3.6W typical power consumption, 4W for the /NP model    
    Dimensions & weight   Shockproof rugged aluminum enclosure, (L: 115 x W: 64 x H: 35 mm), 370 g with the cable and without the antenna    
    Standards   MIL-STD-810F method 514.5 & 516.5 (shocks & vibrations), IP65 seal rating EN 301489-17 & EN 61000-6-2 (CEM), E-marked (2004/104)    
    Environment   Operating temperature: -25°C to +70°C (HR 0-99%), storage: -40°C to +80°C    

WLg-xROAD/N

Actualmente estamos trabajando en mostrarte los mejores resultados, si no encuentras el producto que buscas contacta con nosotros a través de info@er-soft.com o al número Tel. +34 916-408-408
Bienvenido a ER-Soft.
ER-Soft con la ley orgánica de protección de datos
Política de cookies.
Utilizamos cookies propias y de terceros para mejorar nuestros servicios y mostrarle publicidad relacionada con sus preferencias mediante el análisis de sus hábitos de navegación.
Si continúa navegando, consideramos que acepta su uso.
Más información pulsando aquí
X

¿Necesitas ayuda? Click

ayuda ER-Soft
X
Consulta a ER-Soft. *

 

*

 

* *Campos obligatorios.




X